Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process.ġ. ![]() To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization) procedure. MikroTik warrants all RouterBOARD series equipment for the term of twelve (12) months from the shipping date to be free of defects in materials and workmanship under normal use and service, except in case of damage caused by mechani-cal, electrical or other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of na-ture. All trademarks and registered trademarks appearing in this manual are the property of their respective holders. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. No part of it may be reproduced or transmitted in any form without prior written permission from the copyright holder. This manual contains information protected by copyright law. Hold this button during boot time longer, until LED turns off, and then release it to make RB750look for Net-install servers.Ĭurrently tested operating system is MikroTik RouterOS starting from version v5.Ĭopyright and Warranty Information Copyright MikroTikls SIA. Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configura-tion (same result as with RouterOS reset hole) RouterBOOT reset button (RESET, front panel) has two functions: Hold screwdriver in place until RouterOS configuration is cleared. Must short circuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. ![]() You can use this procedure if you have forgotten the password to access the device, or simply wish to return the unit to its default configuration state.īuttons and Jumpers RouterOS reset jumper hole (on the bottom of case, behind one of the rubber feet) resets RouterOS software to de-įaults. Hold this button during boot time until LED lights start flashing, then release the button to reset RouterOS configuration. In case you wish to return the RB750device to its original configuration, you can use the RESET button which is located to the left of the Ethernet ports. The First Ethernet port accepts 8.28 V DC powering from a passive PoE injector. More information here: Įxtension Slots and Ports Five individual Gigabit Ethernet ports, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or cross-over cables for connecting to other network devices. In case IP connection is not available, Winbox can also be used to connect to the MAC address of the device. In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of the device when starting it until the LED light turns off, and Groove will start to look for Netinstall servers. Winbox should be used to connect to the default IP address of 192.168.88.1 with the username admin and no password. This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility. Please see detailed configuration guide here: ![]() Normally the power consumption of this device is 2.4W, under maximum load - 3.6Wīooting process RouterOS is the operating system of all RouterBOARD routers. Powering The board accepts powering from the power jack or from the first Ethernet port (Passive PoE):ĭirect-input power accepts 8.28V DC, device comes bundled with aįirst Ethernet port accepts passive Power over Ethernet accepts 8-28V DC RB750 Default IP address from LAN is 192.168.88.1 Set LAN computer IP configuration to automatic (DHCP)ģ. Connect your WAN cable to port 1, and LAN computers to ports 2-5Ģ. ![]() Quick Setup Guide and Warranty Informationįirst use 1. RouterBOARD 750 The RB750 is a low cost Ethernet router.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |